★欢迎光临巩义市大千净化材料有限公司官方网站！☞硫酸亚铁、一水硫酸亚铁、七水硫酸亚铁、农用硫酸亚铁、聚合硫酸铁☎0371-69580958
Polyferric Sulfate Product Introduction
Chinese name of chemical: polyferric sulfate, solid polyferric sulfate (referred to as solid polyferric sulfate or SPFS) molecular formula: [Fe2 (OH) n (SO4) 3-N / 2] m (where n < 2, M = f (n))
Technical specification code: bk-113-06 Main component: ferric sulfate (polymerization) Iron sulfate content: 20-21%
CASNo.：35139-28-7
Appearance and character: yellow or reddish brown amorphous powder or granular solid.
PH (10g / L aqueous solution): 2-3 melting point (℃): 190 (253kpa) relative density (water = 1): 2.44
Saturated vapor pressure (kPa): 0.13 (100 ℃)
Solubility: easily soluble in water, alcohol, chloroform, carbon tetrachloride, slightly soluble in benzene.
1. New type, high quality and high efficiency ferric salt inorganic polymer flocculant; 2. It has excellent coagulation performance, dense alum and fast settling speed;
3. No harmful substances such as aluminum, chlorine and heavy metal ions, no water phase transfer of iron ions, non-toxic, harmless, safe and reliable;
4. It can remove turbidity, decolorization, deoiling, dehydration, bacteria, odor, algae, COD, BOD and heavy metal ions;
5. The pH range of the water body is 4-11, and the optimum pH range is 6-9. After purification, the pH value and total alkalinity of the raw water change little, and the corrosion to the treatment equipment is small;
6. The results show that the purification effect is remarkable for micro polluted, algae containing, low temperature and low turbidity raw water, especially for high turbidity raw water;
7. The dosage is small, the cost is low, and the treatment cost can be saved by 20% - 50%.
Executive standard: national standard of the people's Republic of China "water purifying agent polyferric sulfate" (GB 14591-2016)
|
Total iron content, % , ≥ |
18.5 |
19.1 |
|
Content of reducing substance (calculated by Fe2 +)% , ≤ |
0.15 |
0.01 |
|
Basicity% |
9.0-14.0 |
14 |
|
PH(1% aqueous solution) |
2.0-3.0 |
2.4 |
|
Arsenic (as) content , % , ≤ |
0.0008 |
0.0001 |
|
Lead (PB) content , % , ≤ |
0.0015 |
0.0001 |
|
Insoluble content , % , ≤ |
0.5 |
0.4 |
When using polymeric ferric sulfate, generally the liquid polymeric ferric sulfate is mixed into 10%- 50% aqueous solution (in the source water turbidity is higher can be directly added), the solid polymeric ferric sulfate is mixed into 10%- 30% aqueous solution, and then according to the specific situation will be mixed solution according to the best conditions and dosage input, after full stirring can get the best coagulation effect. The dosage can be measured according to the different turbidity of raw water, the best dosage, generally turbidity (turbidity in 100-500mg/L) water, 30 to 50 kg per thousand tons, non-drinking water high turbidity industrial sewage can be appropriate dosage. In the treatment of industrial wastewater, the polyferric sulfate is diluted to an aqueous solution of 1-2 times. When the source water concentration is higher and the treatment water quantity is larger, it can be added directly. Then according to the results of the laboratory simulation test according to the best process conditions and dosage, after full stirring, coagulation settlement, can get clarification of the effluent.
